Metal wheeled wheel sets for Ratio 00 Wagon Kits

Discussion in 'Kits, Kit bashes & Scratch builds' started by Tallpaul70, Aug 14, 2019.

  1. Tallpaul70

    Tallpaul70 Full Member

    Messages:
    205
    Likes Received:
    95
    Joined:
    Mar 2, 2019
    Hi All,
    Can anyone suggest a type and source of metal wheeled wheel sets to replace the plastic wheel sets supplied in 00 Ratio wagon Kits?
    All the Hornby and Bachmann wheel sets are too short in the axle. They have c25mm axles but the Ratio kits require c28mm axles.
    I think the standard Maygib and those supplied with Parkside kits are also too short for the Ratio kits.

    Many thanks
    Paul
     
  2. paul_l

    paul_l Staff Member Administrator

    Messages:
    9,849
    Likes Received:
    5,902
    Joined:
    Dec 5, 2015
    Do you have brass bushes fitted in the axel boxes. If not then these may be your saviour, fit the bushes into the axel box holes (a little MEK in the hole to soften the plastic may help), then see if the wheel sets fit.

    Paul
     
    Tallpaul70 and Mr Porter like this.
  3. Tallpaul70

    Tallpaul70 Full Member

    Messages:
    205
    Likes Received:
    95
    Joined:
    Mar 2, 2019
    I don't think that brass bushes will take up the 3mm slack unless they are only partially inserted into the axle boxes. If they are not fully inserted, how can you be sure that they are square to the axle?
    Has anyone experience of this solution?
    Many thanks
    Paul
     
    jakesdad13 likes this.
  4. Gary

    Gary Wants more time for modelling.... Staff Member Administrator

    Messages:
    7,316
    Likes Received:
    3,847
    Joined:
    Dec 5, 2015
    I was going to suggest Steam Era Models wheel sets but they only come with 23.8mm, 25mm or 26mm axles. http://steameramodels.com/wheels.htm

    Could you glue a 1.5mm thick piece of pre-drilled styrene over the axle boxes to take up the slack then use the brass bushes ??

    Cheers, Gary.
     
    Tallpaul70 likes this.
  5. jakesdad13

    jakesdad13 Staff Member Moderator

    Messages:
    4,535
    Likes Received:
    2,071
    Joined:
    Dec 14, 2015
    Are these Ratio kits NOS (new old stock)? Reason I ask is that newer, current kits come with metal wheel sets with brass top hat bushes that you drill, I think 2mm, and insert before assembling the kit. The axleboxes are fitted with their W irons to the sole bars then glued to the wagon base with the wheels and axles fitted and held in place for a short while for the glue to grab. Once it has dried and all is solid the axles can rotate freely without to much end float.
    The top hat bushes can be bought from (for example) Romfords or Alan Gibson, the same for metal wheel sets.
    If the wagon is already assembled it is possible to buy a tool that fits between the two axle boxes and has a very small short drill bit at one end to open up the axle boxes to except the bushes. It is also useful for opening up the boxes on RTR 00 wagons for fitting brass bearings. Dunno who makes them though, though a google search may throw up some suggestions.

    Cheer's, Pete.
     
    Tallpaul70 likes this.
  6. Mr Porter

    Mr Porter Failure is always an option. Full Member

    Messages:
    184
    Likes Received:
    148
    Joined:
    Oct 7, 2017
    DCC Concepts do them. DCF-BR2

    :headbanger:

    Jim
     
    Tallpaul70 and jakesdad13 like this.

Share This Page